The Aether Battery System from Aether Biomedical is made for robotic hands only, and it is installed inside the prosthetic socket. It powers the prosthesis and its components.
For clinicians, that design shapes the whole fitting. Clinicians set compatibility before planning the socket, place the components during fabrication, and explain the charging rules at handover.
Aether describes the system as an integrated power solution with real-time monitoring and USB-C charging. The figures below come from the Aether Battery System Instructions for Use (IFU), version 8, and Aether’s own product information.
The Aether Battery System (AET-BAT-BS1) is a power system for upper-limb prostheses. Its battery pack is fixed to the inner surface of the socket, and its charging port is mounted into the socket wall.
Its main parts are:
|
Component |
Part code |
Role |
|
Battery pack |
AET-BAT |
Powers the prosthesis; fixed to the inner surface of the socket |
|
Battery charging port |
AET-CHR |
Mounted into the socket; has a USB-C connector, one button and four LEDs |
|
Connector board |
AET-CON |
Connects the battery pack and the charging port; provides a 2-pin kidney-style output to the terminal device |
|
Charging accessories |
AET-USBC, AET-PWR-USB-xx |
1 m USB cable (USB-A to USB-C) and an AC/DC power adapter for the country of use |
|
Charging port covers |
AET-COV |
Covers for the charging port |
|
Fabrication aids |
AET-DUM, AET-CUT, AET-DRL |
Help with the socket fabrication process |
The Aether Battery System is intended for use exclusively with Zeus hands.
Use with non-Zeus multi-articulating hands is not supported and has not been validated by the manufacturer. The IFU also lists a contraindication: the system cannot be used with devices other than those specified by Aether Biomedical.
The battery and the bionic hand it powers are documented to work together by the same manufacturer. Before a fitting, check the full configuration against the Compatibility Guide (U03DC-0200) referenced in the IFU.
The AET-CHR charging port is mounted into the prosthetic socket and secured with a biocompatible adhesive. According to the IFU, it has a USB-C connector and is used with the AC/DC power adapter provided.
Aether's charging guidance and the IFU give these details:
The four LEDs on the charging port show the battery's charge level, whether the system is on, and whether charging is in progress or finished. Pressing the port's button turns the LEDs on.
|
LED behavior |
What it means |
|
LEDs light after pressing the button |
The current charge level, in four ranges: below 25%, 25 to 50%, 51 to 75% and 76 to 100% |
|
LEDs glow constantly for 3 seconds |
The system is turned on |
|
LEDs blink 3 times |
The system is turned off |
|
Last LED blinks quickly 6 times after a button press with the system off, or blinks constantly with the system on |
The charge level is critically low |
|
Blue LEDs light |
Charging is in progress |
|
All LEDs blink twice, then turn off |
Charging is finished |
The AET-CON connector board connects the battery pack and the charging port, and it provides a 2-pin kidney-style output connector to the terminal device.
Two IFU rules apply when connecting it. The connectors only attach one way, so they should never be forced, and every wire should be connected to the correct connector and properly oriented. The IFU also recommends applying an electrically insulating compound.
The IFU lists these specifications for the system:
|
Specification |
Aether Battery System (AET-BAT-BS1) |
|
Voltage output |
7.2V DC nominal; 8.4V DC at full charge |
|
Current output |
Up to 10A peak; 5A continuous |
|
Nominal capacity |
2800mAh (+0%, -10%) |
|
Charging current and time |
Up to 1.2A; up to 5 hours |
|
Power adapter |
Input 100 to 240V AC, 50 to 60Hz; output 5.0V DC, 2.4A |
|
Service life |
Up to 2 years or 500 charge/discharge cycles |
|
Operating temperature |
0°C to +50°C |
|
15% to 93% |
|
|
Operating pressure |
700 to 1060 hPa |
|
Dimensions |
AET-BAT: two cells (22 x 65 mm) connected with a 110 mm cable; AET-CHR: 45 x 20 mm; AET-CON: 20 x 30 mm |
|
Weight |
AET-BAT: 102 g; AET-CHR: 11 g; AET-CON: 4 g |
|
Storage |
Recharge every 6 months if unused |
|
Use |
Single-patient use |
The battery pack should not have direct contact with the user's skin or be mechanically stressed, and the batteries should not be bent.
The Aether Battery System includes three fabrication aids for building the socket around it:
Installation of the Aether Battery System is for qualified personnel, and the clinician provides the socket. Aether Biomedical does not make sockets.
Before the first fitting, review the installation steps in the Aether Battery System IFU, and confirm the full configuration against the Compatibility Guide it references. Clinicians who want to see the components before planning a socket can book a demo with Aether Biomedical.
No. Its intended use is limited to the Zeus hand, and non-Zeus multi-articulating hands are not supported or validated.
Press the button on the charging port. The LEDs light to show the current charge level.
With the system off, the last LED blinking quickly 6 times after a button press means the charge level is critically low. With the system on, the last LED blinks constantly instead.
No. The Aether Battery System does not supply power to the prosthesis while charging, and charging should take place with the prosthesis and socket disconnected from the patient.
Its service life is up to 2 years or 500 charge/discharge cycles.
If it isn’t being used, recharge it every 6 months.
Stop using it if you notice unusual heat, gases, color change, or an abnormal appearance while it is charging or discharging.
Contact the manufacturer or distributor. Don’t replace the AET-USBC cable or AET-PWR-USB-xx adapter with another cable or adapter.
Through the WEEE process, not with household waste.
The Aether Battery System is a socket-mounted power system made for Zeus hands only. Its charging port is mounted into the socket, and its battery pack is fixed inside it, with the connector board linking the two. Its fabrication aids help clinicians build the socket, and its specifications are documented in the Aether Battery System IFU.
To see the Aether Battery System working with Zeus hands, book a demo with Aether Biomedical.